Unbekanntes Gerät? - 7720G?

mm987

Neuer Benutzer
Moin, moin!
Ich habe ein Aspire 7720G - 702G25Mi und habe heute Vista neu installiert. Nun habe ich ein unbekanntes Gerät im Gerätemanager mit der Hardware ID: ACPI\ENE0100 unter Recourcen steht: E/A-Bereich FF2C - FF2F und IRQ: 0x00000004 (4) Ich habe keine Ahnung was das ist? Kann mir einer von euch sagen, was das ist, damit ich den richtigen Treiber installieren kann?

Gruß
 

mm987

Neuer Benutzer
Oke :-(
Ich blicke das Tool grade noch nicht zu 100%

wenn ich auf detect drücke steht da unten in dem Fenster:

Device 2448h 82801HBM Hub Interface to PCI Bridge (ICH8M B1 step)
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision F3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge (PCI to PCI (Subtractive Decode))
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 7, Subordinate Bus Number 7
Secondary Bus Command 0000h ()
Secondary Bus Status 2280h (Supports Back-To-Back Trans., Received Master Abort, Medium Timing)
Secondary Bus Latency 20h
I/O Port Range Passed to Secondary Bus : None
Memory Range Passed to Secondary Bus : 97000000h to 970FFFFFh
Prefetchable Memory Range Passed to Secondary Bus : None
New Capabilities List Present:
Subsystem ID & Subsystem Vendor ID Capability
SSVID : 100037h
SSID : 010030h

PCI\VEN_8086&DEV_2815&SUBSYS_00000000&REV_03
Bus 0 (PCI Express), Device Number 31, Device Function 0
Vendor 8086h Intel Corporation
Device 2815h 82801HEM (ICH8M-E) LPC Interface Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 03h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge (PCI to ISA)
Subsystem ID 011E1025h Unknown
Subsystem Vendor 1025h Acer Inc
New Capabilities List Present:
Vendor-Dependant Capability

PCI\VEN_8086&DEV_2850&SUBSYS_011E1025&REV_03
Bus 0 (PCI Express), Device Number 31, Device Function 1
Vendor 8086h Intel Corporation
Device 2850h 82801H (ICH8 Family) Ultra ATA Storage Controllers
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 03h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Storage (IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Subsystem ID 011E1025h Unknown
Subsystem Vendor 1025h Acer Inc
Address 0 is an I/O Port : 00000000h
Address 1 is an I/O Port : 00000000h
Address 2 is an I/O Port : 00000000h
Address 3 is an I/O Port : 00000000h
Address 4 is an I/O Port : 000060E0h
System IRQ 11, INT# A

PCI\VEN_8086&DEV_2829&SUBSYS_011E1025&REV_03
Bus 0 (PCI Express), Device Number 31, Device Function 2
Vendor 8086h Intel Corporation
Device 2829h Mobile SATA AHCI Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 02B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back Trans., Medium Timing)
Revision 03h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Storage (Serial ATA (AHCI 1.0))
Subsystem ID 011E1025h Unknown
Subsystem Vendor 1025h Acer Inc
Address 0 is an I/O Port : 000060F8h
Address 1 is an I/O Port : 00006114h
Address 2 is an I/O Port : 000060F0h
Address 3 is an I/O Port : 00006110h
Address 4 is an I/O Port : 00006020h
Address 5 is a Memory Address (anywhere in 0-4Gb) : 9B304000h
System IRQ 19, INT# B
New Capabilities List Present:
Message Signalled Interrupt Capability MSI is
disabled MSI function can generate 32
-bit addresses
Power Management Capability, Version 1.2
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D3hot
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
SATA HBA Optional Features Present

PCI\VEN_8086&DEV_283E&SUBSYS_011E1025&REV_03
Bus 0 (PCI Express), Device Number 31, Device Function 3
Vendor 8086h Intel Corporation
Device 283Eh 82801H (ICH8 Family) SMBus Controller
Command 0003h (I/O Access, Memory Access)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 03h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Serial (SMBus Controller)
Subsystem ID 011E1025h Unknown
Subsystem Vendor 1025h Acer Inc
Address 0 is a Memory Address (anywhere in 0-4Gb) : 9B305000h
Address 4 is an I/O Port : 00006000h
System IRQ 11, INT# B

PCI\VEN_10DE&DEV_0407&SUBSYS_011E1025&REV_A1
Bus 1 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0407h GeForce 8600M GT
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A1h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Display (VGA)
Subsystem ID 011E1025h Unknown
Subsystem Vendor 1025h Acer Inc
Address 0 is a Memory Address (anywhere in 0-4Gb) : 92000000h
Address 1 is a Memory Address (anywhere in 64-bit space, Prefetchable) : 80000000h
Address 3 is a Memory Address (anywhere in 64-bit space) : 90000000h
Address 5 is an I/O Port : 00005000h
System IRQ 16, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability MSI is
disabled MSI function can generate 64
-bit addresses
PCI Express Capability, Version 1
Device/Port Type :
PCI Express Endpoint Device
Device Capabilities :
Device Control : Unsupported Request Severity is
Fatal
Device Status :
Link Capabilities : Maximum Link Speed :
2.5Gb/s Maximum Link Width : x
16
Link Port Number : 0

Was sagt mir das jetzt alles? :-(


Gruß
 

mm987

Neuer Benutzer
Ja! Ich habe Vista einfach so installiert, da meine Recoverypartition zerschossen war (andere Geschichte)

Naja nun muss ich halt alles Treiber installieren. Habe ich auch soweit (denke ich) Ist halt nur noch diese eine Sache die fehlt.


Gruß
 
Oben