Aspire 1810TZ UMTS und BT nachrüsten, Akkulaufzeit, OS, Treiber?

hausrocker

Neuer Benutzer
Ich habe ein 1810tz-352G25n und ein 1810tz-412g25n.


Das 352 hat ja nur den SU3500 - sprich core 2 solo CPU, dafür aber Bluetooth.
Angeblich ist das Modul dafür unter der Tastatur,


Es gibt ja folgende Anleitung im Netz, bei ebay werden auch die BT Module verkauft.
So, here is the description of my Acer Aspire 1410 Bluetooth Module install, and what to be careful of:
1. Shutdown Acer Aspire 1410 Netbook, unplug A/C adapter, remove battery.
2. Ground self to metal USB, VGA, or HDMI to remove static electricity.
3. Remove keyboard by pressing down to release tiny black tabs (4 at rear and 1 on each side).
4. Remove keyboard blue cable by lifting black connection lever with thumbnail.
5. Remove screws under keyboard labeled "M2x3L" and "M2x5L" (3 silver M2-3L and 6 black M2X5L).
6. Remove blue mouse pad cable by lifting black connector lever with fingernail.
7. Close display and flip over to expose bottom of Acer Aspire 1410 Netbook.
8. Remove hard drive cover with the 2 black M2X5L screws.
9. Lift cream colored hard drive gold cable connector with two fingernails or small flat screwdriver prying up gradually on each side.
10. Remove hard drive by pulling the clear plastic pull tab.
11. Loosen 12 black M2X5L screws on bottom, then flip the 1410 over on a towel to capture all 12 screws.
12. Flip Acer Aspire 1410 Netbook over right side up.
13. Lift top case that surrounds keyboard with fingers and release tiny black tabs on inside of display hinges by pressing in with tiny flat screwdriver while lifting top case around hinge areas.
14. Connect Bluetooth Module Cable to module with white connector.
15. Place Bluetooth Module in carrier on lower case by pressing down onto existing clear double stick tape and plastic guide pins to lock-in module.
16. Plug Bluetooth Module Cable black connector into white motherboard plug.
17. (*Very Important*) From Bluetooth module, run cable down into existing cable slot on lower case toward other wires and tuck excess cable under motherboard. *If this is not done to route Bluetooth Cable properly, the cable will interfere with the mouse right-click button, which will cause the mouse pad not to work.
18. Reassemble making sure that hard drive, mouse pad, and keyboard connections are proper, in this order: Top case snap in black tabs by hinges, hard drive, hard drive cover, bottom 12 screws, mouse pad cable, 9 screws under keyboard, keyboard cable, and keyboard.
19. Install battery and turn on the Acer Aspire 1410 11.6 inch display Netbook.
20. Turn on the Bluetooth using the switch at the left-front of the case, next to the Wi-Fi switch.
21. Download the proper driver (Vista, XP, or whatever you reloaded the 1410 with), and unzip to the "C" drive or desired location.
22. Use the automatic driver install wizard that starts to browse to the driver folder, and finish the driver install.
23. Use the newly installed Bluetooth as desired
Außerdem diesen Hinweis:
Hi all,

I have noticed that we only need to open a little bit the bottom part of the case, by removing some screws near the part where the BT goes. No need to disassembly hard disk, touchpad or keyboard, just to have a precission clip (sorry for my english) and, after retiring the screws, open carefully the case with some help. Then pull off the white film on the carrier to access the adhesive film and place there the BT module, previously connected to the cable. After that we only need to be patient inserting the other end of the cable into the 5-pin plug located on the motherboard with the precission clip. The only left to be done is to allocate the cable inside the case and close with the screws.

Doing this, I only needed to retire 7 screws from the back of the case, and the 2 screws belonging to the hard disk cover, nothing else.

Now I have my bluetooth module working properly without risk of damaging the computer.

Ivan
Sobald meine beiden Geräte hier sind werde ich das auf jeden Fall mal testen und auch berichten, wie es aussieht mit den Garantiesiegeln, ob man die irgendwie unbeschadet gelöst bekommt, wenn sie etwas warm sind oder evtl. gar nicht betroffen sind.

Das und noch einiges mehr gibt es hier in dem Beitrag in einem Englischen Forum: [Acer Aspire 1410/1810t/1810tz] Timeline Tweaks (2)
Da gibt es auch Leute, die sich bereits die interne UMTS Karte nachgerüstet haben, das Problem ist wohl, dass die Stelle, wo die Karte sein soll, bzw. kann auch den MiniPCI Connector nicht hat, den muß man also auch selbst auflöten erst. Was wohl nur für geübte Leute mit passendem Equipment überhaupt möglich ist. (Kann man sehen, wenn man unten das Platikcover abschraubt, wo auch der Arbeitsspeicher sitzt. Siehe auch hier, oberes Video: http://project-r.org/cgi-bin/diarypro/archives/904.html )

Ansonsten hätte ich ja gerne hier auch Erfahrungswerte von anderen 1810 Besitzern, wie lang euer Akku hält, wenn ihr auch den 5600mAh Akku habt, welches OS ihr installiert habt und ob schon mal jemand XP prof 32 bit mit Windows 7 ultimate 64bit vergleichen hat in Bezug auf Leistung, Treiber, Akkulaufzeit?

In meinem 1810t ist im moment eine Intel WiFiLink 5100 Karte verbaut. Ich bekomme aber keine 300 Mbit Verbindung mit meinem WRT320N Router (dualband) hin, mit meinem Asus mit 802.11n ging es wenigstens schon mal mit 150 Mbit (da nur eine Antenne). Kann die WiFi Link 5100 Karte überhaupt 40 Mhz Kanalbreite? Ich habe auch schon mit "upper" und "lower" umgestellt, damit anstelle der 802.11a Frequenz die 802.11b/g Frequenz genutzt wird für die breiten Kanäle, kein Unterschied. Treiber sind vom 04.03.2009 - Version 12.4.0.21. Jemand ne Idee, woran das liegt? In den Treibereinstellungen habe ich überall auto gewählt, explizit 802.11n aktivierbar ist da ja eh nicht.
 
Zuletzt bearbeitet:

Crusoe

Neuer Benutzer
AW: Acer Timeline 1810tz - UMTS und BT nachrüsten, Akkulaufzeit, OS, Treiber?

Ich habe ein 1810tz-352G25n und ein 1810tz-412g25n.


Das 352 hat ja nur den SU3500 - sprich core 2 solo CPU, dafür aber Bluetooth.
Angeblich ist das Modul dafür unter der Tastatur,

Stimmt, ist beim 1810 auch so :) Und das BT-Modul kann man für 20€ bei eBay kaufen, das geht wunderbar :)



Das und noch einiges mehr gibt es hier in dem Beitrag in einem Englischen Forum: [Acer Aspire 1410/1810t/1810tz] Timeline Tweaks (2)
Da gibt es auch Leute, die sich bereits die interne UMTS Karte nachgerüstet haben, das Problem ist wohl, dass die Stelle, wo die Karte sein soll, bzw. kann auch den MiniPCI Connector nicht hat, den muß man also auch selbst auflöten erst. Was wohl nur für geübte Leute mit passendem Equipment überhaupt möglich ist. (Kann man sehen, wenn man unten das Platikcover abschraubt, wo auch der Arbeitsspeicher sitzt. Siehe auch hier, oberes Video: x-gadget:blog )

Hab ich mit meinem 1810TZ versucht, hat nicht geklappt :(
SIM Slot und MiniPCI-E habe ich sehr sorgfältig verlötet, das UMTS Modul aus meinem 1810T wurde trotzdem nicht erkannt. Aber es wurde warm, also irgendwas war da schon...

Ansonsten hätte ich ja gerne hier auch Erfahrungswerte von anderen 1810 Besitzern, wie lang euer Akku hält, wenn ihr auch den 5600mAh Akku habt, welches OS ihr installiert habt und ob schon mal jemand XP prof 32 bit mit Windows 7 ultimate 64bit vergleichen hat in Bezug auf Leistung, Treiber, Akkulaufzeit?
Akku läuft mit Win7 Ultimate 64Bit ca 6 Stunden im Officebetrieb.
XP hab ich nicht installiert bekommen (0x7b Bluescreen bei der Installation)
Egal ob mit oder ohne F6-Knopf Treiber (SATA Treiber)
Egal ob IDE oder AHCI Modus im BIOS.

In meinem 1810t ist im moment eine Intel WiFiLink 5100 Karte verbaut. Ich bekomme aber keine 300 Mbit Verbindung mit meinem WRT320N Router (dualband) hin, mit meinem Asus mit 802.11n ging es wenigstens schon mal mit 150 Mbit (da nur eine Antenne). Kann die WiFi Link 5100 Karte überhaupt 40 Mhz Kanalbreite? Ich habe auch schon mit "upper" und "lower" umgestellt, damit anstelle der 802.11a Frequenz die 802.11b/g Frequenz genutzt wird für die breiten Kanäle, kein Unterschied. Treiber sind vom 04.03.2009 - Version 12.4.0.21. Jemand ne Idee, woran das liegt? In den Treibereinstellungen habe ich überall auto gewählt, explizit 802.11n aktivierbar ist da ja eh nicht.

Ich hab auch eine 5100 und ich schaffe die 300MBit (Netto 100MBit).
Man bedenke das die 300MBit (bei DD-WRT auf dem Router) nur erreicht werden können wenn man: WPA2-AES benutzt, 5GHz N-Modus und 40MHz Kanalbreite verwendet, anders habe ich es nicht hinbekommen.

Ich weiß der Beitrag ist schon was älter, aber mir haben schon Antworten in Beiträgen geholfen die erst nach 4 Jahren gekommen sind :)
 
Oben